How to fix the front facing FaceTime camera in a Verizon or Sprint iPhone 4

How-to-replace-the-front-facing-FaceTime-camera-in-a-Verizon-or-Sprint-iPhone-4

If you enjoy using FaceTime or Skype with your friends, family, and colleagues, the front facing camera on your iPhone is probably pretty important to you. If it starts malfunctioning or stops working, a DIY repair isn't too difficult and will cost you far less than replacing your Verizon or Sprint iPhone 4.

Disclaimer: As with any repair, neither iMore nor PXLFIX can be held responsible for any damage you may do to your device. It’s also worth considering that opening up your device to perform any repair or modification can and will void your Apple warranty. If you don’t feel comfortable opening your device, don’t. Use extreme care and caution when performing a repair on any device.

What you need for a DIY CDMA (Verizon or Sprint) iPhone 4 front facing camera replacement

PXLFIX recommends using only quality and genuine parts from a reputable supplier like eTech Parts. They have quality parts, tools, and much more for all your repair needs.

  • CDMA iPhone 4 (please note there ARE internal differences between the GSM and CDMA models - this guide strictly deals with the CDMA model - in the US, that means Verizon or Sprint)
  • Replacement front facing camera - Link to part
  • #00 Phillips screwdriver
  • Flat blade screwdriver
  • Pry tool or spudger
  • Security screwdriver (to remove the 2 screws in your dock connector, all CDMA models will come with security screws)

Power off your iPhone 4

iPhone slide to power off

Before performing any repair, always power off your device before removing any screws or parts.

Remove the back

    Remove the dock connector screws on your CDMA iPhone 4
  1. First remove the bottom 2 dock connector screws in your iPhone 4. Use your five point security screwdriver for this as all versions of the CDMA iPhone 4 have security screws in the dock connector.
  2. Remove the back of your CDMA iPhone 4
  3. To remove the back simply slide the back upwards and lift it off gently.
  4. Set the back and 2 dock connector screws aside.

Organize your screws

It's very important to make sure you remember where you are pulling screws from, so place them in an arrangement that you'll understand and remember. I normally lay them out the same way every time I disassemble a device so I remember where they came from and how they go back in. They're all different sizes so trying to figure out where they go if you get them mixed up probably won't be fun.

Remove the battery

    Remove battery screw iPhone 4 CDMA
  1. To remove the battery you’ll need to remove the #00 screw holding the battery clip in place. Remove this screw located to the bottom left of the battery.
  2. Remove battery clip iPhone 4 CDMA
  3. The metal clip on the battery is what clips the battery to the logic board. You’ll need to pop this clip up with your plastic pry tool. Simply stick the end of your pry tool underneath the clip and gently pull upwards until it unfastens from the logic board.
  4. Remove battery iPhone 4 CDMA
  5. To remove the battery, I do not recommend using the plastic pull tab. There is quite a bit of adhesive underneath the battery and the tab will normally just rip off or you can bend the battery. Instead, run your pry tool along the right side of the battery and break the adhesive that way. Once the battery is free from the adhesive, you can pull the battery out of the phone. There are no other connectors holding it in.
  6. Fold over battery tab on iPhone 4
  7. I typically fold the plastic tab over while working on the iPhone 4 to keep it out of the way while I'm disassembling parts. It's not necessary but convenient.

Remove the grounding clip

To the left of where you disconnected the battery you'll see another screw holding in a grounding clip over the antenna. We'll need to remove it.

    Remove grounding clip screw on CDMA iPhone 4
  1. Unscrew the one screw holding the grounding clip in place with your #00 Phillips screwdriver.
  2. CDMA iPhone 4 grounding clip for antenna
  3. Gently lift the grounding clip out of the device. It's very tiny as you can see above. Take care not to misplace it or lose it.

Remove the dock connector shield and disconnect the cable

    Remove dock connector shield iPhone 4 CDMA
  1. There is a shield held on with two screws covering the dock connector cable. Remove the two screws holding it in place and set the shield and screws aside, remembering where they came from. (They are labeled as screw 1 & 2 in the photo above.)
  2. Remove dock connector cable iPhone 4 CDMA
  3. Next, use your pry tool to pry up the actual dock connector cable. Be careful as there is adhesive holding the cable in place as well. Peel back the adhesive gently to free the cable.

Unclip the antenna from the logic board

Underneath where you removed the grounding clip, you'll see a tiny circular cable. This is your antenna cable. You'll need to unclip it from the logic board.

  1. Take the edge of your pry tool or spudger and gently pry up the circular head to detach it from the logic board.
  2. Unclip antenna cable iPhone 4 CDMA
  3. You'll notice the cable is wound around some metal brackets. Just gently guide it out of the brackets with your pry tool and finger. It's attached to the speaker assembly. Once you've finished unwinding it from the brackets, you can leave it where it is for now.

Remove the top logic board shield

    Remove logic board shield screws CDMA iPhone 4
  1. There are 5 screws holding the logic board shield in place as labeled in the photo above. Remove the 5 screws holding it in place plus screw number 6 off to the right (we'll get to this one in a second). Just be sure to remember which holes they came out of as the screws are different sizes. I keep them arranged in the shape they came out of the logic board with the shield next to it. I find this to be the easiest way to keep them in order.
  2. Remove logic board shield CDMA iPhone 4
  3. Next you'll need to remove the shield. There is a tiny clip built into the shield holding it in place. (Refer to the photo above.) Grab the shield by the top where the top screw came out and gently lift up and push down. The bottom notch will come out and you should be able to gently lift the shield out of the device.

Remove wifi antenna grounding clip

    Remove wifi grounding clip screw CDMA iPhone 4
  1. The number 6 screw we removed previously we're now returning to. There is a clip underneath it. Gently use your pry tool to remove it.
  2. Remove wifi grounding clip CDMA iPhone 4
  3. You'll find a cross head screw underneath it. We'll get back to that in just a minute.

Disconnect 7 cables from the logic board

    Remove cables from logic board iPhone 4 CDMA
  1. Pop up all the cables labeled in the pictures above by gently lifting them with your pry tool or spudger..
  2. Remove CDMA iPhone 4 CDMA Camera
  3. Next gently lift the camera out of the device. You'll notice there is a tiny tab that is seated underneath the LCD and digitizer cables to the right.
  4. iPhone 4 CDMA cables removed from logic board
  5. Play close attention to the direction in which the cables pop up. The cable furthest to the right will pop up in the opposite direction of the others.

Remove the logic board

    Logic Board Screw Placement CDMA iPhone 4
  1. There are 5 screws you'll need to remove in order to remove the logic board. Three need to be removed with a flat blade screwdriver (flathead) while the other two will be removed with your #00 Phillips screwdriver.
  2. Remove the screws numbered 1-3 in the image above using your flat blade screw driver. Make sure you remember which ones go where as the heads are a bit different.
  3. Now remove screws 4 and 5 with your #00 screwdriver. Notice that the screw labeled number 5 will have a tiny gold grounding clip for the camera underneath it. Make sure you don't lose this and save it for re-assembly.
  4. Remove the logic board on a CDMA iPhone 4
  5. You should now be able to remove your logic board. Holding it at the bottom, gently pull it upwards. I use my other hand to lift up at the top where the rear facing camera used to be.
  6. Logic board grounding clip iPhone 4 CDMA
  7. Take note that there is a small rubber piece that sits at the top of the logic board. You will need this for re-assembly so make sure it doesn't fall off. If you lose this, you could experience wifi or reception issues.

Remove the metal retainer & front facing camera

How-to-remove-iPhone-4-camera-retainer

There is a metal retainer covering the front facing camera. To remove it use your pry tool to gently pull it off. Make sure you don't lose it as you'll need it for reassembly. Now that the metal retainer has been removed you can gently lift the front facing camera out of the iPhone 4.

Replace the front facing camera & metal retainer

remove-iPhone-4-front-facing-camera

Now replace the front facing camera with the new replacement part. Once it is securely in place you can replace the metal retainer by snapping it back in place.

Reassemble your iPhone 4

Once you've gotten the front facing camera seated in correctly and the metal retainer snapped back into place to hold it down, you're ready to finish putting your Verizon or Sprint iPhone 4 back together. To do so you can either follow these directions in reverse order or you can refer to our reassembly video above.

Since the reassembly video covers an almost complete teardown, you can go ahead and forward to around 3:30 and follow the directions from that point.

And...done!

After you've managed to get all the pieces of your iPhone 4 put together and the screws back snug into their homes, you should be able to power it up. Tap into the camera icon and test out the front facing camera to make sure all went well. If it did you should now have a fully functioning front facing camera again so you can get back to FaceTiming and Skype calling.

Want to know how to perform another type of iPhone repair or modification? Send me suggestions to ally.kazmucha@imore.com.

For questions or to inquire about mail-in repairs through PXLFIX, please follow us on Twitter, like us on Facebook or e-mail us directly! Of course, you can like us and follow us just because you think we're cool too!

Additional Resources:

Allyson Kazmucha

Help and how to editor for iMore. I can take apart an iPhone in less than 6 minutes. I also like coffee and Harry Potter more than anyone really should.

More Posts

 

0
loading...
0
loading...
28
loading...
0
loading...

← Previously

Dead Trigger review for iPhone and iPad

Next up →

Why Apple would release a 7-inch iPad

Reader comments

How to fix the front facing FaceTime camera in a Verizon or Sprint iPhone 4

4 Comments
Sort by Rating

But iPhones "just work and never ever fail, Steve jobs said so.. Please remove this article now you have been corrected...

awesome article plz visit my blog too
i m also writing a blog on apple
The Unofficial Apple Blog. Daily news ranging from iPhone, iPhone apps review,software,mobile to latest news.
Join us Apptec.net, your Apple Community.

Somebody essentially help to make significantly articles I would state. That is the first time I frequented your website page and thus far? I surprised with the analysis you made to create this particular publish amazing. Fantastic activity!

iPhone Repair Experts, Same Day Shipping. Get Started Now, iPhone Repair – iPhone 3G, 3Gs, 4, 4S, iPod 4 Repair, iPad 1, 2, 3, Repair, iMac G5, G6, Repair, MacBook Pro, Air, Repair,
http://www.clinic4iphone.org
Call or Text: 281-310-0858
iphone glass replacement
iphone 4 glass replacement
iphone 4 front glass replacement
iphone 4 back glass replacement
iphone 4 digitizer replacement
repair iphone 4
iphone 4 water damage
iphone 4s screen replacement
iphone 4s lcd replacement
iphone 4s back glass replacement
iphone 4 repairs
iphone 4s repair service
iphoe 4 repair service
i phone 4 service
replacement glass for iphone 4