On one hand it's a bold move, dumping something everyone's familiar with for something new, which is very typically Apple. On the other hand, it's not dumping it for something really, truly new, like Palm-style inductive wireless charging.

While a lot of accessories would continue to work as long as they or Apple provided an adapter, some might not, and then you'd have to buy them again. And if you have a lot of accessories or even cables, it's either impractical to get an adapter for each one, or annoying to keep having to switch the adapter.

Rene laid out a good case for why Apple could be getting ready to pull the trigger on a smaller dock connector, so now we want to hear what you think about it. Do you want Apple to ditch the current dock? Pro or con or couldn't care less?

An updated "micro dock" would make room for bigger batteries, 4G radios, and other components far more important to the iPhone and iPad in a PC free world.

We've heard that Apple is getting ready to ditch the dock connector as it's currently sized and implemented on iPods, iPhones, and iPads. The reason isn't anything political, like a new desire to conform to an outdated micro-USB standard, but typically Apple: to save space inside the iPhone 5 for what are now more important components.

There are some precedents for this. Apple switched from the very common mini SIM card to the then very uncommon micro SIM card for the original iPad. They took the antenna out of the core package and put it around the edge in the iPhone 4. They had 10 hours of battery life they wanted to hit. They had a Retina display and its backlight. They had an HSPA radio. They had 802.11n Wi-Fi. They had a bigger camera sensor. They had a lot of power-hungry components, and they needed space to hold them and power them, so they switched to a smaller SIM and kicked the antenna to the outside.

The dock connector, while not huge, still takes up space that could otherwise go to what are now more important components like battery and LTE radios

The dock connector as it exists now is a relatively big component that takes up, while not a lot of space compared to the entire assembly, a lot of space compared to the difference between mini and micro SIM.

4G LTE radios also take up a lot of space. Apple has waited on better, smaller chipsets, and won't be going to a form-factor the size of the Galaxy Nexus or Nokia Lumia 900 any year soon, but every square millimeter they can save inside the device will matter.

The importance of the dock connector has also changed. When the iPhone 4 was released, iOS was not yet PC free. There was no iCloud. There was no AirPlay. There was no Bluetooth 4.0.

Apple cut-the-cord to iTunes with iOS 5. Cutting the 30-pin dock connector down to size is a logical next step.

The 30-pin dock handled all syncing and data transfer, including backups, music, movies, and other media, all car and other connections, even video-out dongles. Over the years it changed slightly, most significantly the change from FireWire to USB-only charging, but up until now it did all the heavy lifting.

Up until now. Backups are easier and better over iCloud. Wi-Fi sync can handle even large media files, if not as quickly, still relatively painlessly given their average frequency. Video and screen mirroring just bean straight to the Apple TV. Accessories can connect and interact over the air. The iTunes app tether has been appreciably cut, so the timing to cut down on the dock connector might never be better.

Apple has also reduced the size of connectors in their Mac line, going to the PCI Express and Mini DisplayPort based Thunderbolt connector almost across the line (Mac Pro the lone holdout).

iOS devices probably can't go Thunderbolt since they doesn't use PCI Express architecture, but that doesn't mean the dock port can't get smaller, doing everything it still needs to do in a PC free world, and saving Apple precious space inside the iPhone 5 package.

(I'm saying iPhone 5 because we haven't heard a specific timeline. iPad 3 is a much bigger device which may not be facing the physical size constraints of the iPhone yet. iPad did get the micro SIM first, however, so it's possible Apple could be looking to debut a newer, smaller dock connector on that device first. We just haven't heard anything specific about it and so think iPhone 5 is more likely.)

Apple probably won't go micro-USB either, because it's not faster and not Apple's style.

A smaller dock connector -- a "micro dock" if you will -- makes a lot more sense.

Not all current accessories would be compatible, of course, even if Apple offered an adapter dongle. It would upset as many customers as it would thrill. But Apple had never been afraid to ruthlessly jettison the past for a better future. Just ask the floppy drive, and now the optical drive and FireWire port.

Apple is fearless when it comes to driving the future. And the dock connector might be next on their list.

If your iPhone 3G or iPhone 3GS is having trouble charging, picking up a signal, or has a dead mic or speaker - replacing the dock assembly should remedy any of these problems. It can also solve issues with an unresponsive home button. A DIY dock assembly repair is an easy enough fix if you've got the right tools and about thirty minutes to spare.

Disclaimer: As with any repair, TiPb nor PXLFIX can be held responsible for any damage you may do to your device. It’s also worth considering that opening up your device to perform any repair or modification can and will void your Apple warranty. If you don’t feel comfortable opening your device, don’t. Use extreme care and caution when performing a repair on any device.

What replacing a dock assembly fixes

• Microphone
• Dead speaker
• Charging port
• Wifi and 3G antennas
• Unresponsive home button (This problem can be caused by two issues - the dock connector or digitizer assembly. If replacing the dock connector does not correct the issue, try replacing your digitizer assembly.)

What you need for a DIY dock assembly repair

PXLFIX recommends using only quality and genuine parts from a reputable supplier like eTech Parts. They have quality parts, tools, and much more for all your repair needs.

• A sad iPhone 3G or iPhone 3GS
• A replacement dock connector assembly (while the repair is very similar for both 3G and 3GS users, the part is different so make sure you order the correct one for your device) - iPhone 3G dock assembly, iPhone 3GS dock assembly
• A #00 Phillips screwdriver
• A suction cup
• A plastic pry tool or spudger
• A SIM removal tool or paperclip

Power off your iPhone

Before performing any repair, always power off your device before removing any screws or parts.

Remove the dock connector screws

Using your #00 Phillips screwdriver, remove the 2 screws located on each side of the dock connector.

Remove the digitizer & LCD assembly

This part can be a bit tricky so please do this with extreme care so you don't tear any cables during the process. I highly recommend using the suction cup method unless your screen is cracked above the home button for some reason and you can't get a proper seal with the suction cup.

Suction cup method (recommended):

The easiest way to remove the digitizer assembly is by using a suction cup.

1. Position the suction cup on the screen directly above the home button.
2. Using your other hand, hold down the frame while gently pulling up on the suction cup.
3. The goal is to get the bottom of the digitizer loose. Do not pull directly up. There are 3 cables attached in the top right of your iPhone. You do not want to tear these. Just pull up until the bottom of the assembly pops out.
4. After you have the bottom up you can remove the suction cup.

Spudger/razor blade method (only use this method as a secondary method):

ONLY use this method if your screen is cracked above the home button. If this is the case, you'll need to use a razor blade or spudger in order to remove it. And while you're at it, replace that broken screen!

1. Starting in the bottom left hand corner, insert a plastic spudger and gently pry up. Once the first side is starting to pop up, do the same on the bottom right side.
2. Run your pry tool along the bottom of the device in order to pop up the bottom of the assembly. Take special care around the home button area.

Remove the cables that attach the digitizer assembly to the logic board:

Once you have the bottom of your digitizer assembly popped up we can remove the cables attaching it to the logic board.

1. Gently lift up your digitizer enough to have a clear view of the 3 cables in the top right of your iPhone.

2. With your plastic spudger or pry tool, you'll need to pry up the first two cables that attach the digitizer and LCD. They should be labeled with orange stickers numbered 1 and 2. Simply pop them off the logic board gently.

3. Underneath these cables you'll see one other labeled as cable 3. This one is a bit trickier as it is clipped down. You'll need to gently pop up the clasp holding it into the fastener. It is a tiny white clip. Simply pop it upwards and the number 3 cable should then slide right out.

4. Remove the digitizer & LCD assembly and set it aside.

Remove your SIM card

Using your SIM tool or a paperclip, either works, remove your SIM card and tray from your device.

Unclip cables from the logic board

1. Towards the top left of the logic board, use your pry tool to pop up the two cables labeled 5 and 6.

2. Towards the bottom of the logic board, 3G owners will only see one cable to the left labeled 4. 3GS users will see two cables (one on each side of the dock connector) labeled 4 and 7. 3G users will just pop up the number 4 cable while 3GS owners will need to pop up both the number 4 and 7 cables.

Remove your logic board

1. Remove the 8 screws outlined in the video that hold the logic board in place. One of the screws is under a Do not remove sticker at the bottom right by the dock connector. Obviously you'll have to remove the sticker to get to it.

2. Make sure you place the screws in an order you will remember. They are different sizes in some instances so you'll need to make sure you put them back in the correct order.

3. Notice the screw holding the camera in place has a metal bracket underneath it. Just take care not to lose this as you'll need to put it back during reassembly.

4. Gently pop your camera up with your spudger or pry tool.

5. Insert your pry tool in the space between the dock connector and logic board and gently pry upward to loosen the logic board.
6. Gently grab the bottom of the logic board and slide it out downwards to remove it.

Remove the old dock connector

3G owners

1. Remove the two screws on either side of the bottom of the dock connector.
2. To remove the dock connector gently pull it up and out.
3. Take note of how the brackets for the screws go above the screw holds in the casing. You'll need to make sure this is how you line up the new dock connector.

3GS owners

1. Remove the two screws on either side of the bottom of the dock connector.
2. Remove the screw underneath the number 4 cable holding the dock connector into the casing.
3. To remove the dock connector gently pull it up and out.
4. Take note of how the brackets for the screws go above the screw holds in the casing. You'll need to make sure this is how you line up the new dock connector.

And... done!

If you followed all the steps above correctly you should be able to power on your phone and be on your way! Test the dock connector out to make sure it's fully functional by checking wifi, placing a test call, and attempting to charge it.

Have you done this repair yourself? Let us know how it went! Want to know how to perform another type of iPhone repair or modification? Send me suggestions to ally.kazmucha@imore.com or leave a comment in our brand new Mod and DIY Repair Forum!

For questions or to inquire about mail-in repairs through PXLFIX, please follow us on Twitter, like us on Facebook or e-mail us directly! Of course, you can like us and follow us just because you think we're cool too!

No sooner did we ask you if Apple should ditch the dock, than Apple Insider reports that the mobile phone and smartphone industries are beginning to come together on a universal charging solution, and that solution is micro-USB.

So far, early signees for the 2012 initiative include AT&T, LG, Motorola, Nokia, Orange, Qualcomm, Samsung, Sony Ericsson, T-Mobile, and Vodafone. Several iPhone carriers there, but not the single iPhone creator, Apple.

Of course, Apple and their licensees have invested heavily in the proprietary 30-pin dock connector, so we have to ask: facing a micro-USB standard, will that be an increasing competitive advantage, or a growing problem?

The iPhone, like the iPod before it (well, at least since the 3rd-gen iPod, when Apple switched from FireWire), uses a proprietary connector called the dock for charging, syncing, video and audio-out, and multiple other functions. A broad port with 30 pins for many purposes, having a proprietary connector gives Apple a lot of flexibility, but also -- through their licensing program -- a lot of control over who can make peripherals and what can be done with them.

During our last edition of the iPhone Live! podcast, Dieter flat-out stated that Apple needed to dump the dock. He pointed out that countries like China and regions like the EU are, or may be, making universal connectors like USB a legal requirement. One charger, one port, to rule them all. (HTC is already replacing the 3.5mm headphone jack, folding it into the mini-USB-like ExtUSB on devices like the Android G1).

The dock connector originally allowed Apple to keep FireWire compatibility and add USB when it entered the PC market. Over time, Apple has moved over to USB, and now with the iPhone 3G and later iPod's, FireWire is gone completely and charging can only occur via USB. Since USB already provides power, provides data exchange, and technology like DisplayLink (which connects external displays via USB) show that an increasingly large range of connection types are becoming possible.

So, as technology marches on, as backwards compatibility is shed, and as standards like USB 2.0 (and in the future, USB 3.0) grow faster and more capable, is it time for Apple to dump the dock and go with the same port most everyone else is using (including Apple with the Mac)?