You're in luck: A screen replacement is a relatively easy repair to perform. You'll just need a few tools and a new digitizer assembly to make your broken iPhone 3G or 3GS good as new! (Psst: This repair can also fix an unresponsive home button as well.)
Disclaimer: As with any repair, iMore cannot be held responsible for any damage you may do to your device. It's also worth considering that opening up your device to perform any repair or modification can and will void your Apple warranty. If you don't feel comfortable opening your device, don't. Never use any type of conductive tool to pry or lift cables. Always use a plastic pry tool or spudger. And of course, make sure your device is powered off before beginning any repair work.
What you'll need
iMore recommends using only quality and genuine parts from a reputable supplier like iFixYouri. They have the proper parts and tools for all your repair needs.
Note: While the steps for this repair are the same for both phone models, the part is different so make sure you order the correct digitizer assembly for your device.
- iPhone 3GS digitizer assembly
- iPhone 3G digitizer assembly
- Suction cup
- Standard #000 Phillips screwdriver
- Spudger tool
- Razor blade
- iSesamo Opening tool (not necessary but awesome for prying up cables and getting under adhesive)
Power off your phone
First things first, power off your device. Hold down the power button and slide to power off. Once the device is completely off, move on to the next step.
Remove the dock connector screws
Using your #00 Phillips screwdriver, remove the 2 screws located on each side of the dock connector.
Remove the old digitizer assembly
This part can be a bit tricky so please do this with extreme care so you don't tear any cables during the process.
Suction cup method (recommended):
The easiest way to remove the old digitizer is by using a suction cup to pull up the old screen.
- Position the suction cup on the screen directly above the home button.
- Using your other hand, hold down the frame while gently pulling up on the suction cup.
- The goal is to get the bottom of the digitizer loose. Do not pull directly up. There are 3 cables attached in the top right of your iPhone. You do not want to tear these. Just pull up until the bottom of the assembly pops out.
- After you have the bottom up you can remove the suction cup.
Spudger/razor blade method (only use this method as a secondary method):
If your screen is cracked above the home button, a suction cup may not create a seal strong enough for you to pull the digitizer up. If this is the case, you'll need to use a razor blade or spudger in order to remove it.
- Starting in the bottom left hand corner, insert a plastic spudger and gently pry up. Once the first side is starting to pop up, do the same on the bottom right side.
- Run your pry tool along the bottom of the device in order to pop up the bottom of the assembly. Take special care around the home button area.
Remove the cables that attach the digitizer assembly to the logic board:
Once you have the bottom of your digitizer assembly popped up we can remove the cables attaching it to the logic board.
- Gently lift up your digitizer enough to have a clear view of the 3 cables in the top right of your iPhone.
- With your plastic spudger or pry tool, you'll need to pry up the first two cables that attach the digitizer and LCD. They should be labeled with orange stickers numbered 1 and 2. Simply pop them off the logic board gently.
- Underneath these cables you'll see one other labeled as cable 3. This one is a bit trickier as it is clipped down. You'll need to gently pop up the clasp holding it into the fastener. It is a tiny white clip. Simply pop it upwards and the number 3 cable should then slide right out.
- Remove the digitizer assembly and set it aside for LCD removal.
Remove the LCD from the old assembly and place it in the new assembly
- There are 6 screws holding the LCD in place. They are all the same size. Three on the left side of the frame, 2 on the right side of the frame, and 1 on the top right holding down the induction flex. Remove all 6 screws with your #00 Phillips screwdriver and set them aside.
- Next use your pry tool to slowly work the LCD out of the old assembly on the left and right sides. It should come out fairly easily. Just take special care not to scratch it while removing it. The LCD and back plate will remove in one piece as they are glued together.
- Re-position the LCD and frame in the new assembly and replace all 6 screws in the new assembly. Make sure to remove any protection film on the inside of the new assembly before putting in the LCD. This is also a good time to check for dust between the LCD and new digitizer. I use air duster when necessary to make sure none gets stuck on the inside of the device.
Reassemble the digitizer
- Begin with the number 3 cable that clips down. Getting it seated can be a bit tricky. Use a plastic spudger to guide it in the opening if needed. Then push back down the clip that holds it in place.
- Next push down the number 1 and 2 cables onto the logic board.
- To snap the new digitizer assembly back in place, start at the top and make sure it is lined up. Once the top is pushed down and flush, snap the bottom into place on each side of the home button.
- Replace the two dock connector screws.
That's it! You now have a brand new digitizer on your iPhone 3G or 3GS! Turn your iPhone back on and test the digitizer. If the touchscreen is unresponsive, remove the digitizer again and verify that the number 2 cable is pushed down all the way onto the logic board and seated correctly. Also test your proximity sensor while making a call and make sure it is functioning properly.
Have you done this repair yourself? Let us know how it went!
We may earn a commission for purchases using our links. Learn more.
Apple Music TV is all music, all the time, and free for all
Apple today announced a new MTV-like music streaming channel – but you'll need to be in the United States to enjoy it.
Potential iPhone 12 Pro unboxing video shows super shiny, super boxy sides
Is this the first video of an unboxed iPhone to reach the internet? If it is, you're going to need sunglasses when you get yours.
Apple is extending its free year of Apple TV+ for another three months
Apple has begun emailing some Apple TV+ subscribers, informing them that they are extending their free year trial by another three months.
Protect your iPhone 8 without adding bulk with an ultra-thin case
Looking for an ultra-thin, super lightweight, barely-there case for your iPhone 8? We gotcha covered.